Zilla's rebuild (exhaust mod revealed, gauges going in.....)
#351
Senior Member
True Car Nut
Joined: May 2003
Posts: 8,135
Likes: 1
From: Lethbridge, Alberta, _______Canada._______ West Coast Bonneville Fest ___05,06,07 Survivor___
i bet the car cant wait to be put in R and get the HELL out of that garage its been cooped up inside forever!
#355
Left hand looks worse than it is. I did knick a couple fingers modifying the plug wire retariners a couple nights ago. Right hand is worse than it looks. I was beat last night, but kept at it.
The side-gapped plugs are a test. I want to see how they go. That'* a tricky little operation all by itself.
When I get some coffee in me and clear my head, I'll post a list of what'* left to do.
The side-gapped plugs are a test. I want to see how they go. That'* a tricky little operation all by itself.
When I get some coffee in me and clear my head, I'll post a list of what'* left to do.
#357
Update on the list:
This leaves:
RF inner fender liner and wheel/tire.
Remove jackstands.
Install Crossover pipe heat shield
Install both belts.
Install strut bar (no need to do this before lowering the car, all strut nuts are still on the car)
Re-route the charcoal canister to it'* new location.
Install 2nd MAP sensor and run it'* wires and the new trans temp sender'* wires through the firewall.
Fill oil and coolant.
Install washer reservior
Install FWI
Install OEM MAP bracket
Here'* how she sits this morning:
Originally Posted by willwren
On the list for tonight :
RF inner fender liner and wheel/tire. STILL NEED TO DO
Remove jackstands. STILL NEED TO DO
Install 6 spark plugs and finish routing/looming wires. DONE
Install TB and throttle cable bracket. DONE
Install Crossover pipe heat shield STILL NEED TO DO
Finish FWI, and connect all sensors (8 that I can think of). DONE
Install heater hose bypass o-ring and reconnect both heater hoses. DONE
Install both belts. STILL NEED TO DO
Install strut bar (no need to do this before lowering the car, all strut nuts are still on the car) STILL NEED TO DO
Install all vacuum lines, and re-route the charcoal canister to it'* new location. STILL NEED TO DO
Drill and install new thermostat. DONE
Install EGR. DONE
Install O2 DONE
Install BCS/BCA. DONE
Install 2nd MAP sensor and run it'* wires and the new trans temp sender'* wires through the firewall. STILL NEED TO DO
Fill oil and coolant. STILL NEED TO DO
Put battery on charger for tomorrow'* starting attempt. DONE
Install washer reservior
Install FWI
List subject to change as I remember more little things still not done.
RF inner fender liner and wheel/tire. STILL NEED TO DO
Remove jackstands. STILL NEED TO DO
Install 6 spark plugs and finish routing/looming wires. DONE
Install TB and throttle cable bracket. DONE
Install Crossover pipe heat shield STILL NEED TO DO
Finish FWI, and connect all sensors (8 that I can think of). DONE
Install heater hose bypass o-ring and reconnect both heater hoses. DONE
Install both belts. STILL NEED TO DO
Install strut bar (no need to do this before lowering the car, all strut nuts are still on the car) STILL NEED TO DO
Install all vacuum lines, and re-route the charcoal canister to it'* new location. STILL NEED TO DO
Drill and install new thermostat. DONE
Install EGR. DONE
Install O2 DONE
Install BCS/BCA. DONE
Install 2nd MAP sensor and run it'* wires and the new trans temp sender'* wires through the firewall. STILL NEED TO DO
Fill oil and coolant. STILL NEED TO DO
Put battery on charger for tomorrow'* starting attempt. DONE
Install washer reservior
Install FWI
List subject to change as I remember more little things still not done.
RF inner fender liner and wheel/tire.
Remove jackstands.
Install Crossover pipe heat shield
Install both belts.
Install strut bar (no need to do this before lowering the car, all strut nuts are still on the car)
Re-route the charcoal canister to it'* new location.
Install 2nd MAP sensor and run it'* wires and the new trans temp sender'* wires through the firewall.
Fill oil and coolant.
Install washer reservior
Install FWI
Install OEM MAP bracket
Here'* how she sits this morning:
#360
Looking very nice under that hood of yours Bill!!! im sure this has been answered and more than likely buried in this thread, but what did you paint the SC with? I've been wanting to paint mine for weeks now.
Thanks
Thanks