homemade rotors?
#11
Senior Member
True Car Nut
Thread Starter
![Default](https://www.gmforum.com/images/icons/icon1.gif)
rather i know reliablity factor of drilling through hardened rotors is slim but what im saying is you can drill through hardened rotors
#13
Senior Member
Posts like a Corvette
Join Date: Jan 2003
Posts: 1,250
Likes: 0
Received 0 Likes
on
0 Posts
![bmsgaffer86 is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Originally Posted by willwren
Sure, but you better do it on an endmill with a rotary indexer, or you're going to have a sever balance issue, too.
Here in KenTUCKy all yous need is sum kentucky fire water,sum duck-tape, a front yard full of cars, and grampy'* old winchester!
![Alcoholic](https://www.gmforum.com/gm/images/smilies/alcoholic.gif)
![2 Guns Firing](https://www.gmforum.com/gm/images/smilies/2gunsfiring_v1.gif)
(do NOT take that seriously! [/disclaimer] )
#14
Senior Member
Certified GM nut
Join Date: Feb 2003
Location: Georgia
Posts: 2,095
Likes: 0
Received 0 Likes
on
0 Posts
![DrJay is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Originally Posted by willwren
Wire EDM is the preferred method of drilling or machining hardened materials, particularly when you get to the RC 58-60 range or harder in steels. However.......
Then you know all about stress cracks in hardened materials. You weaken the rotor by drilling after hardening, and even somewhat STILL if you drill before hardening. The holes need to be CAST into the blanks to prevent stress cracks (before hardening) to be suitable fore everyday street use, and still provide no real benefit to you other than looks, and decreasing the surface area 'bite' that the pads can achieve. Crossdrilling will in effect REDUCE your ability to brake.
Slotting, however, has proven benefits, and doesn't cause the stresscracking problem. Slots allow the pad to outgas, preventing a gas layer from being trapped in between the pad and rotor (imagine an air hockey table.....same effect). Slotting also allows water to escape, further improving wet braking, and allows pad friction material to be effectively removed from the rotor.
Then you know all about stress cracks in hardened materials. You weaken the rotor by drilling after hardening, and even somewhat STILL if you drill before hardening. The holes need to be CAST into the blanks to prevent stress cracks (before hardening) to be suitable fore everyday street use, and still provide no real benefit to you other than looks, and decreasing the surface area 'bite' that the pads can achieve. Crossdrilling will in effect REDUCE your ability to brake.
Slotting, however, has proven benefits, and doesn't cause the stresscracking problem. Slots allow the pad to outgas, preventing a gas layer from being trapped in between the pad and rotor (imagine an air hockey table.....same effect). Slotting also allows water to escape, further improving wet braking, and allows pad friction material to be effectively removed from the rotor.
![Admin Ownz](https://www.gmforum.com/gm/images/smilies/admin4.gif)
#15
Senior Member
Posts like a Corvette
Join Date: Jan 2004
Location: Montréal, QC
Posts: 1,374
Likes: 0
Received 0 Likes
on
0 Posts
![Foghorn is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Originally Posted by GAMEOVER
can you make your own crossdrilled rotors? and slot them?
Originally Posted by willwren
No, and no.
Cheers,
#17
Junior Member
Posts like a Ricer Type-R
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Slotting, yes. If you have the proper tools. Drilling? I still say no. Slotting won't cause stress fractures like drilling will. You have to get into the physics of it.
Yes, you can drill your own rotors, but they won't be rotors any more. They'll be scrap metal.
So no, you can't drill your rotors. You can drill what you don't intend to use as rotors any more!
Yes, you can drill your own rotors, but they won't be rotors any more. They'll be scrap metal.
So no, you can't drill your rotors. You can drill what you don't intend to use as rotors any more!
![Laughing](https://www.gmforum.com/gm/images/smilies/icon_lol.gif)
#18
Senior Member
Posts like a Corvette
Join Date: Jan 2004
Location: Montréal, QC
Posts: 1,374
Likes: 0
Received 0 Likes
on
0 Posts
![Foghorn is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
I'm not a fan of cross drilled rotors...and it'* really not worth doing the slotting yourself as opposed to buying them slotted...unless you just like to play around
Cheers,
![Wink](https://www.gmforum.com/gm/images/smilies/icon_wink.gif)
Cheers,
#19
Senior Member
True Car Nut
Thread Starter
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Originally Posted by Foghorn
I'm not a fan of cross drilled rotors...and it'* really not worth doing the slotting yourself as opposed to buying them slotted...unless you just like to play around
Cheers,
![Wink](https://www.gmforum.com/gm/images/smilies/icon_wink.gif)
Cheers,
#20
Senior Member
Posts like a Northstar
Join Date: Feb 2004
Location: Fargo, ND
Posts: 685
Likes: 0
Received 0 Likes
on
0 Posts
![lglarum is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Did these guys have a little too much fun with the drill??
http://cgi.ebay.com/ebaymotors/ws/eB...category=33564
would these be bad even if they were drilled then hardened?
http://cgi.ebay.com/ebaymotors/ws/eB...category=33564
would these be bad even if they were drilled then hardened?