Fixing the wifes truck
#1
Thread Starter
Joined: May 2006
Posts: 29,661
Likes: 34
From: Sheboygan Wisconsin
Fixing the wifes truck
The wheel hub on my wifes truck was making noise, so I picked up a new hub and went to replacing it.
P2280274.jpg
New hub.
P2280275.jpg
Took far more time getting the old one off then it did putting the new on on.
P2280276.jpg
Had a little extra time so I cleaned up the shop, it really needed it. Then I decided to run some hard line from the air compressor. Tapped in to the tank and put on a ball valve.
P2280277.jpg
Then hooked up a regulator and ran a 3/4" id hose to the wall. From here I will use steel pipe.
P2280278.jpg
P2280274.jpg
New hub.
P2280275.jpg
Took far more time getting the old one off then it did putting the new on on.
P2280276.jpg
Had a little extra time so I cleaned up the shop, it really needed it. Then I decided to run some hard line from the air compressor. Tapped in to the tank and put on a ball valve.
P2280277.jpg
Then hooked up a regulator and ran a 3/4" id hose to the wall. From here I will use steel pipe.
P2280278.jpg
#4
Thread Starter
Joined: May 2006
Posts: 29,661
Likes: 34
From: Sheboygan Wisconsin
It'* a 2005 Montana.
Took about a hour and a half. My Bonneville had a nice notch to tap a screwdriver in to and it came right out. This one is flush all the way around. I put a bunch of penetrating oil, then I heated it with a torch. It took a fair amount of hitting the screwdriver to get it to move. then I got a small screwdriver in and opened up the gap and was able to pry it out. I cleaned it up and the new one went right in.
Took about a hour and a half. My Bonneville had a nice notch to tap a screwdriver in to and it came right out. This one is flush all the way around. I put a bunch of penetrating oil, then I heated it with a torch. It took a fair amount of hitting the screwdriver to get it to move. then I got a small screwdriver in and opened up the gap and was able to pry it out. I cleaned it up and the new one went right in.
#6
Thread Starter
Joined: May 2006
Posts: 29,661
Likes: 34
From: Sheboygan Wisconsin
Not sure if it'* the same as the 2000+ I know my 97 the bolt goes from the outside in. On this one the bolt goes from the inside out and threads in to the hub. The old hub was really hard to turn by hand. I would say it was bad.
#8
Thread Starter
Joined: May 2006
Posts: 29,661
Likes: 34
From: Sheboygan Wisconsin
Great, I fix one thing and she finds something else to grumble about. She'* picking up a new power steering pump. And she wants the struts changed, those will have to wait a bit. I find it funny that when I'm in the shop working on my car, it'* wasting my time, when I'm working on someone else' car, I'm wasting my time, but when it'* her truck, I better drop everything and fix it.
#9
Great, I fix one thing and she finds something else to grumble about. She'* picking up a new power steering pump. And she wants the struts changed, those will have to wait a bit. I find it funny that when I'm in the shop working on my car, it'* wasting my time, when I'm working on someone else' car, I'm wasting my time, but when it'* her truck, I better drop everything and fix it.
When she grumbles about fixing someone elses car it wouldn't be one of your girlfriend'* cars would it? LOL
#10
Thread Starter
Joined: May 2006
Posts: 29,661
Likes: 34
From: Sheboygan Wisconsin