p0200 code 03 Savana Van..no inj. signal on #2
#1
Senior Member
Posts like a Northstar
Thread Starter
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Working on an '03 Savana Van (5.3).... showing P0200 code, along with the P0300 and P0302..... tested with a noid light if I had signal to the injectors.... I have flash to every injector but the #2 Cylinder Injector...... I tested the wire and I have 12 volts on the power lead, and I have 12 volts on the ground lead....... Therefore, BAD ECM? BAD Cam sensor? Ideas?
#2
Retired
![](https://www.gmforum.com/images/ranks/veteran_army.png)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Why are you thinking CAM sensor? CAM doesn't drive the injectors.
12v power should always be on on the + of the injector when power is on. The PCM controls the GRND of the injector.
Disconnect the injector and measure the voltage with power on from a known good chassis ground.
12v power should always be on on the + of the injector when power is on. The PCM controls the GRND of the injector.
Disconnect the injector and measure the voltage with power on from a known good chassis ground.
__________________
Retired Administrator
Retired Administrator
#3
Senior Member
Posts like a Northstar
Thread Starter
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Only reason I mentioned CAM was that I talked to an ASE Certified Mech. friend of mine this afternoon, and he mentioned an outside possibility of this..... I've tested the hot lead and have 12 volts there, and at the Negative side too, so I know it has a good ground....I'm thinking a Driver in the ECM is causing this problem.
#4
Retired
![](https://www.gmforum.com/images/ranks/veteran_army.png)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
If you have 12v+ on the negative side of the injector(when the injector is disconnected) you need to find out why/where this 12v+ is coming from.
__________________
Retired Administrator
Retired Administrator
#6
Retired
![](https://www.gmforum.com/images/ranks/veteran_army.png)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Then its fine.
P0200 is the injector controller(PCM)
P0300 is a random misfire on ALL cylinders.
P0302 is a misfire on #2
You can't use a test light when testing injector circuits.
P0200 is the injector controller(PCM)
P0300 is a random misfire on ALL cylinders.
P0302 is a misfire on #2
You can't use a test light when testing injector circuits.
__________________
Retired Administrator
Retired Administrator
#8
Retired
![](https://www.gmforum.com/images/ranks/veteran_army.png)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Do a continuity check between the PCM connector and injector 2. Then test for short to ground on both circuits
__________________
Retired Administrator
Retired Administrator
#9
Senior Member
![](/images/badges/ASECertified.png)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
![](https://www.gmforum.com/attachments/gmc-chevrolet-truck-suv-177/14160-p0200-code-03-savana-van-no-inj-signal-2-0996b43f80241366.gif?dateline=1457835804)
Tested negative just with my light, and it came on just fine to test ground.
#10
Retired
![](https://www.gmforum.com/images/ranks/veteran_army.png)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Or he tested the circuit wrong.
Use a DVM and put the black wire on GROUND. Then disconnect the injector. Probe BOTH leads to the injector with the RED probe. If you see 12v+ on both injector wires, then you have an issue.
Use a DVM and put the black wire on GROUND. Then disconnect the injector. Probe BOTH leads to the injector with the RED probe. If you see 12v+ on both injector wires, then you have an issue.
__________________
Retired Administrator
Retired Administrator