I need help as soon as possible,Please help.
#1
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Aug 2009
Posts: 183
Likes: 0
From: Wahpeton, North Dakota
I need help as soon as possible,Please help.
I installed new LED tailights on my 2004 GMC yukon XL, they worked great for about two weeks and now both rear lights are not working. The reverse, Turn, brake lights, nothing is there a fuse that would cure this problem. Everything else works on the car but the tail lights. Can anyone plaease point m in the right direction I checked the fuses that sounded like it would be related to the rear light but they all look good/ Is there a fuse under the hood that I need check, I check all my fuses visually and with a Multi Fluke Meter to make 100% certain that they are OK. Please help. If you help me on this Ill mark you down that I owe you one, if you cure it and dont have any problems that I can cure Ill paypal you 20 Bucks. Take Care
#3
Senior Member
True Car Nut
Joined: Sep 2006
Posts: 4,816
Likes: 245
From: Windsor, Ontario / Detroit, Michigan
This link will take you to your owner'* manual. Start on page 5-113 for locations of each fuse box, and what each fuse is for.
http://www.extendedgmwarranty.com/ow...-GMC-Yukon.pdf
Keep your $20. We help people for free.
http://www.extendedgmwarranty.com/ow...-GMC-Yukon.pdf
Keep your $20. We help people for free.
#4
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Aug 2009
Posts: 183
Likes: 0
From: Wahpeton, North Dakota
This link will take you to your owner'* manual. Start on page 5-113 for locations of each fuse box, and what each fuse is for.
http://www.extendedgmwarranty.com/ow...-GMC-Yukon.pdf
Keep your $20. We help people for free.
http://www.extendedgmwarranty.com/ow...-GMC-Yukon.pdf
Keep your $20. We help people for free.
#5
Being that it'* a Denali, I'm betting it does have the PASS Key on it.
My Silverado being an LS, does not. Only a run of the VIN will tell you that.
http://www.compnine.com is where you can do that.
My Silverado being an LS, does not. Only a run of the VIN will tell you that.
http://www.compnine.com is where you can do that.
#7
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Aug 2009
Posts: 183
Likes: 0
From: Wahpeton, North Dakota
Ill call my dealer with the VIN and see if it requires programming. Thank you guys for your help. I was on the TahoeYukon forum and they were just rude over therre with there answer'* and Im glad I found this one Thank you guys for your help and being professional and courtious. Take Care Jonathan
#8
Important:
• To initiate, this procedures requires that a learned master key be available.
• A total of 10 master keys or valet keys may be programmed to a single vehicle.
• This procedure adds keys only. The procedure does not erase previously learned keys.
• The keys to be learned must duplicate the mechanical cut of the current key.
• If more than one valet key is to be learned, immediately precede each valet key with a learned master key.
<LI type=1>With a previously learned master key, turn ON the ignition, with the engine OFF. <LI type=1>Turn OFF the ignition and remove the key.
Within 10 seconds insert the key to be learned. Turn ON the ignition with the engine OFF. The vehicle has now learned the new key.
• To initiate, this procedures requires that a learned master key be available.
• A total of 10 master keys or valet keys may be programmed to a single vehicle.
• This procedure adds keys only. The procedure does not erase previously learned keys.
• The keys to be learned must duplicate the mechanical cut of the current key.
• If more than one valet key is to be learned, immediately precede each valet key with a learned master key.
<LI type=1>With a previously learned master key, turn ON the ignition, with the engine OFF. <LI type=1>Turn OFF the ignition and remove the key.
Within 10 seconds insert the key to be learned. Turn ON the ignition with the engine OFF. The vehicle has now learned the new key.
#9
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Aug 2009
Posts: 183
Likes: 0
From: Wahpeton, North Dakota
Important:
• To initiate, this procedures requires that a learned master key be available.
• A total of 10 master keys or valet keys may be programmed to a single vehicle.
• This procedure adds keys only. The procedure does not erase previously learned keys.
• The keys to be learned must duplicate the mechanical cut of the current key.
• If more than one valet key is to be learned, immediately precede each valet key with a learned master key.
<LI type=1>With a previously learned master key, turn ON the ignition, with the engine OFF. <LI type=1>Turn OFF the ignition and remove the key.
Within 10 seconds insert the key to be learned. Turn ON the ignition with the engine OFF. The vehicle has now learned the new key.
• To initiate, this procedures requires that a learned master key be available.
• A total of 10 master keys or valet keys may be programmed to a single vehicle.
• This procedure adds keys only. The procedure does not erase previously learned keys.
• The keys to be learned must duplicate the mechanical cut of the current key.
• If more than one valet key is to be learned, immediately precede each valet key with a learned master key.
<LI type=1>With a previously learned master key, turn ON the ignition, with the engine OFF. <LI type=1>Turn OFF the ignition and remove the key.
Within 10 seconds insert the key to be learned. Turn ON the ignition with the engine OFF. The vehicle has now learned the new key.
#10
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Aug 2009
Posts: 183
Likes: 0
From: Wahpeton, North Dakota
Ok I think I might have messed up and not noticed, I connected the rear LED lights first and they worked great. Then I installed the LEd turn signal in the front. I never had the Denali out at night to notice if the brake lights or stop lights are not working. So I think its my front turn signal and if I put resistors on my front LED tun signal I think that would cure my problem because I think it all started when I installed the LED turn signals in the front. Its all starting to make sense now. So I will put the old incodescent lights back in the front turn signals and see what that does. Then I will weight for my two 6 ohm 25w resistors to arrive and install them to my front LED and see what that does.