trans gone, now with pictures and questions
#31
Senior Member
Certified GM nut
Thread Starter
Join Date: Dec 2002
Location: plattsburgh NY
Posts: 2,037
Likes: 0
Received 0 Likes
on
0 Posts
actually, to do the diff you dont have to pull the tranny do you? How hard is it to do the diff. Does anyone have a write up?
#32
Senior Member
True Car Nut
Join Date: Aug 2004
Location: In your garage, swipin' da lug nutz
Posts: 3,067
Likes: 0
Received 1 Like
on
1 Post
Hmm...don't think the whole trans has to come out to replace/rebuild just the differential. However, if you get a differently cut differential, you WILL have to pull the trans to replace the related sun gear.
If you could find the right type of diff, I would personally try the diff swap if cash is tight. It would only take a day at the most to do it (you would spend more time than money on it).
If you could find the right type of diff, I would personally try the diff swap if cash is tight. It would only take a day at the most to do it (you would spend more time than money on it).
#33
Senior Member
True Car Nut
Join Date: May 2003
Location: Lethbridge, Alberta, _______Canada._______ West Coast Bonneville Fest ___05,06,07 Survivor___
Posts: 8,135
Likes: 0
Received 1 Like
on
1 Post
Remove the CV on that side, un bolt the housing cover, should be a big Oring in there around the housing you have to change, There is a snapring on the output shaft inside the diff I do belive, the Diff Case should now be able to come out...Your diff case might be damaged too.
You should be able to buy a Spider Gear Pionon Gear Pinon shaft kit with washers, lock pin, and all other needed peices.
You should be able to buy a Spider Gear Pionon Gear Pinon shaft kit with washers, lock pin, and all other needed peices.
#34
Senior Member
Certified GM nut
Thread Starter
Join Date: Dec 2002
Location: plattsburgh NY
Posts: 2,037
Likes: 0
Received 0 Likes
on
0 Posts
ok, so if i can find a diff that is the same then i dont have to remove the tranny and it isnt a bad job. As for the removal, lets see if i have this right, remove axle, remove housing, remove o ring, remove snap ring which is on the output shaft inside the diff, pull out diff. That is the removal? As for the parts matt, is that for rebiuilding the diff? If so could i just buy a used diff and put that in with a new housing and o ring. Then put the axle back in. Do i have this right or no? I am tired and have been studing all day so if i am wrong lol dont B*tch. haha
#35
Senior Member
Certified GM nut
Thread Starter
Join Date: Dec 2002
Location: plattsburgh NY
Posts: 2,037
Likes: 0
Received 0 Likes
on
0 Posts
Ok, the next question would be can i get a list of things i need. I would appriciate it. I know a diff and housing obviously, and probably a new o ring, and new fluid and filter. Anything else. Also doesanyone know what diff i need, and what kind of car it can be out of or any place i can find this kind ofinfo. Thanx guys
#36
Senior Member
Posts like a Camaro
Join Date: Oct 2006
Location: montreal canada NEBF07 ONBF07
Posts: 987
Likes: 0
Received 0 Likes
on
0 Posts
well hope this is better for you tj but you did a good job on exploding that diff case i imagine the noise it made my offer is still there if you need help
#38
Senior Member
Certified GM nut
Thread Starter
Join Date: Dec 2002
Location: plattsburgh NY
Posts: 2,037
Likes: 0
Received 0 Likes
on
0 Posts
actaully i dont do burnouts. lol, yea i can break them loose from a 15 roll and do that everynow and again but actually burnouts i dont do. This car may have done 3 the whole 6 years i have had it. I just dotn see the point of buring the tires on an automatic FWD V6 car, all you are doing is ruining tires and they are not cheap. Now if it was a 6 speed 6.0L GTO maybe haha.
Update, i have thought about it and talked to a few people and i think my best bet is to just get the used tranny. It will cost me like 300 extra, but i will have a lower milage tranny and a 6 month warranty. I think that is the "smarter" thing to do.
Update, i have thought about it and talked to a few people and i think my best bet is to just get the used tranny. It will cost me like 300 extra, but i will have a lower milage tranny and a 6 month warranty. I think that is the "smarter" thing to do.
#40
Senior Member
Certified GM nut
Thread Starter
Join Date: Dec 2002
Location: plattsburgh NY
Posts: 2,037
Likes: 0
Received 0 Likes
on
0 Posts
Seriously, i am not a "oh i can light my tires up guy". Can i lay a patch yes, do i spin my tires at the track for 60' of course my local track is in canada and they have no idea what track prep is haha. As for my mods they are mostly top end mods so far. Those are my passing gear mods haha Actually, as for the 3 burnouts in 6 years, that is 3 burnouts for me, i know my brother drove my car a few times so it is probably like 7