Pulley/Plug/Gap combination
#11
Junior Member
Posts like a Ricer Type-R
Thread Starter
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Nate, way too big of a gap for TR6. You should be TR5 gapped at .055", or TR6 gapped somewhere between 40-45 (however, you don't need 2 ranges colder, so go with the 55).
#12
Senior Member
True Car Nut
Join Date: Sep 2004
Location: Farmington, Minnesota =MWBF '05 SURVIVOR= =CEBF '06 SURVIVOR= =August '06 COTM=
Posts: 9,130
Likes: 0
Received 0 Likes
on
0 Posts
![LakevilleSSEi is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Car whoops *** with the way it'* set now....Mileage jumped up a few too...went from 24mpg hwy to 29 hwy...ZERO KR......
Think i'll leave it alone.
Why all the sudden you telling me to gap them in the 40'* now....last time we talked about my plugs everyone was talking about .50 at the smallest?
Think i'll leave it alone.
Why all the sudden you telling me to gap them in the 40'* now....last time we talked about my plugs everyone was talking about .50 at the smallest?
#13
Junior Member
Posts like a Ricer Type-R
Thread Starter
![Default](https://www.gmforum.com/images/icons/icon1.gif)
You will foul them. I speak from experience on the Zilla from the first time I ran TR6'*:
(taken from Techinfo)
Originally Posted by willwren
I called NGK this morning after noticing the difference in gapping between the TR55 and TR6 (for reference, this is for both the V-Power and Irridiums, and the TR55 is one heatrange colder than stock, TR6 is two heatranges colder).
Factory gapping for us is .060". The TR55 comes that way and is fine. NGK'* website shows the TR6 gapped at .039", and I'd never noticed that before (I was re-gapping mine to .060", and this is what I called to ask them). The tech told me the TR6 is actually gapped at .032", regardless of the website stating .039".
At this point, I asked him what I should be gapping to, based on my mods. He gave me a range of .040" to .045" for the TR6 in my car, and he agreed that because of my hotter MSD coils (and the same would hold true for the 97+ SSEi coils) I should tend to the bigger side, or .045".
The general rule of thumb is never change the gap larger or smaller than factory gapping by .008". In this case, the listed gap of .039" could be safely raised to .047 for my TR6'*, but the ACTUAL gap as I was told of .032" could only be safely gapped up to .040". With that in mind, he told me I'd be fine up to .045", just pushing the PAPER limits. The idea is to keep the faces of center electrode and ground electrode as parallel to each other as possible, and if you go too far, you induce an angle on the ground electrode, so the gap isn't even across the face of the center electrode.
Factory gapping for us is .060". The TR55 comes that way and is fine. NGK'* website shows the TR6 gapped at .039", and I'd never noticed that before (I was re-gapping mine to .060", and this is what I called to ask them). The tech told me the TR6 is actually gapped at .032", regardless of the website stating .039".
At this point, I asked him what I should be gapping to, based on my mods. He gave me a range of .040" to .045" for the TR6 in my car, and he agreed that because of my hotter MSD coils (and the same would hold true for the 97+ SSEi coils) I should tend to the bigger side, or .045".
The general rule of thumb is never change the gap larger or smaller than factory gapping by .008". In this case, the listed gap of .039" could be safely raised to .047 for my TR6'*, but the ACTUAL gap as I was told of .032" could only be safely gapped up to .040". With that in mind, he told me I'd be fine up to .045", just pushing the PAPER limits. The idea is to keep the faces of center electrode and ground electrode as parallel to each other as possible, and if you go too far, you induce an angle on the ground electrode, so the gap isn't even across the face of the center electrode.
#14
Senior Member
True Car Nut
Join Date: Sep 2004
Location: Farmington, Minnesota =MWBF '05 SURVIVOR= =CEBF '06 SURVIVOR= =August '06 COTM=
Posts: 9,130
Likes: 0
Received 0 Likes
on
0 Posts
![LakevilleSSEi is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Well I'll go squash'em down a bit to 43....see where I end up after the week.
#18
DINOSAURUS BOOSTUS
![](/images/badges/Gearhead.png)
Expert Gearhead
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Originally Posted by Foghorn
2.8" pulley
Gen III M90
Autolite 104
0.052"
1997 SSEi L67 Series II Intercooled
Cheers,
Gen III M90
Autolite 104
0.052"
1997 SSEi L67 Series II Intercooled
Cheers,
#19
Senior Member
Posts like a Corvette
Join Date: Jan 2004
Location: Montréal, QC
Posts: 1,374
Likes: 0
Received 0 Likes
on
0 Posts
![Foghorn is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Originally Posted by BillBoost37
I hate you, but love your car
![Idea](https://www.gmforum.com/gm/images/smilies/icon_idea.gif)
Cheers,
#20
Senior Member
True Car Nut
Join Date: May 2003
Location: Holt, MI & Lima, OH
Posts: 3,022
Likes: 0
Received 0 Likes
on
0 Posts
![dbtk2 is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
GTP:
2.55" Pulley
Ported Gen 3 M90
Autolite AR103'* w/.052" gap.
Bonneville:
3.4" Pulley
Gen 3 M90
AC Delco 41-932'* w/.060" gap
Monte Carlo:
3.4" Pulley
Gen 3 M90
AC Delco 41-919'* w/.060" gap
2.55" Pulley
Ported Gen 3 M90
Autolite AR103'* w/.052" gap.
Bonneville:
3.4" Pulley
Gen 3 M90
AC Delco 41-932'* w/.060" gap
Monte Carlo:
3.4" Pulley
Gen 3 M90
AC Delco 41-919'* w/.060" gap