1994 Buick Century, 3.1 V6 Problems!
#11
Retired
#12
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Feb 2014
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
How do you tell a Gen II 3.1 for a Gen III? Look at the upper intake manifold. If it looks like a 1988-1994 style, it;* a Gen II, if it looks like a 1995 to 2002 style it'* a Gen III.
Gen 2 engines are more prone to injector fails.
Either style removing the upper intake is required to access the fuel injectors.
The Test light is connected to the wiring harness on the engine, to check for signal from the ECM to the fuel injectors. Rare on those cars yet 1 out of 1000 might have that issue.
The Injector is checked with a Muilti-Meter on the OHMs Setting. Injectors have to fall between two spec to be acceptable. Injectors not in spec will NEVER fire. GEN II 2.8L & 3.1L engines will often not run at all if one is bad. They will not run at all if two go bad. It'* been a good 8 years since the last one of these I did.
There is a test procedure for Electronic EGR valve. I did it once 10 years ago and don't recall it. Common problem much like 4.3 V6 astro van: carbon chunks hold the pintle open when it should be closed. Others fail in the open position. This allows exhaust gas in to the intake stream at times it should not be entering. This effects the mixture and the ECM freaks out trying to compensate for an issue it can not,.
Gen 2 engines are more prone to injector fails.
Either style removing the upper intake is required to access the fuel injectors.
The Test light is connected to the wiring harness on the engine, to check for signal from the ECM to the fuel injectors. Rare on those cars yet 1 out of 1000 might have that issue.
The Injector is checked with a Muilti-Meter on the OHMs Setting. Injectors have to fall between two spec to be acceptable. Injectors not in spec will NEVER fire. GEN II 2.8L & 3.1L engines will often not run at all if one is bad. They will not run at all if two go bad. It'* been a good 8 years since the last one of these I did.
There is a test procedure for Electronic EGR valve. I did it once 10 years ago and don't recall it. Common problem much like 4.3 V6 astro van: carbon chunks hold the pintle open when it should be closed. Others fail in the open position. This allows exhaust gas in to the intake stream at times it should not be entering. This effects the mixture and the ECM freaks out trying to compensate for an issue it can not,.
I would love to know the test procedure for EGR valve. I took it off and cleaned passage way.
A mechanic also mentioned it could be the ECM? I guess it'* common for the computers to malfunction in Century'* (Gen II)?
Dan
#13
Senior Member
EGR test : https://www.gmforum.com/trouble-shoo...d-test-296250/
Hope that Helps.
Hope that Helps.
__________________
1997 Buick Pk Ave (Soft Ride) Suspension!
1997 Buick Pk Ave (Soft Ride) Suspension!
#14
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Feb 2014
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
EGR test : https://www.gmforum.com/trouble-shoo...d-test-296250/
Hope that Helps.
Hope that Helps.
Anyone know what the specified fuel pressure is at the fuel rail?
#16
Member
Posts like a V-Tak
Gen II vs Gen III in a 1994 Century the ECM'* have about the same fail rate. Both are OBD-I ECM'* with e proms.
Older OBD-i ECM'* some have a single Prom, some have 2 smaller proms. One of those is called a Calibrator.
When you buy a "New" or likely "Re-Manufatored" ECM even from a GM Dealership it will not come with the E-Prom. Often the prom fails with the Computer. Just replacing the computer often does NOT fix the issue.
Either find a good used ECM or buy a nbew one, and find a new E-prom. That is if your going to replace the ECM. Don't replace the ECM for no reason. Narrow down via diagnosis if your ECM is the likely cause.
As for the EGR valve you posted: 1993-1997 3 solenoid style. the test someone posted is a single solenoid style.
#17
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Feb 2014
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
OBD-I ECM'* do tend to fail more then most OBD-II ECM'*.
Gen II vs Gen III in a 1994 Century the ECM'* have about the same fail rate. Both are OBD-I ECM'* with e proms.
Older OBD-i ECM'* some have a single Prom, some have 2 smaller proms. One of those is called a Calibrator.
When you buy a "New" or likely "Re-Manufatored" ECM even from a GM Dealership it will not come with the E-Prom. Often the prom fails with the Computer. Just replacing the computer often does NOT fix the issue.
Either find a good used ECM or buy a nbew one, and find a new E-prom. That is if your going to replace the ECM. Don't replace the ECM for no reason. Narrow down via diagnosis if your ECM is the likely cause.
As for the EGR valve you posted: 1993-1997 3 solenoid style. the test someone posted is a single solenoid style.
Gen II vs Gen III in a 1994 Century the ECM'* have about the same fail rate. Both are OBD-I ECM'* with e proms.
Older OBD-i ECM'* some have a single Prom, some have 2 smaller proms. One of those is called a Calibrator.
When you buy a "New" or likely "Re-Manufatored" ECM even from a GM Dealership it will not come with the E-Prom. Often the prom fails with the Computer. Just replacing the computer often does NOT fix the issue.
Either find a good used ECM or buy a nbew one, and find a new E-prom. That is if your going to replace the ECM. Don't replace the ECM for no reason. Narrow down via diagnosis if your ECM is the likely cause.
As for the EGR valve you posted: 1993-1997 3 solenoid style. the test someone posted is a single solenoid style.
Part 2 -How to Test the Fuel Pump No Start Tests (GM 3.1L, 3.4L)
I would like to CONFIRM this pressure before I order a completely new fuel sender / pump assembly.
Thanks,
Dan
#18
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Feb 2014
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
Now, I just found this information:
http://www.justanswer.com/buick/3nro...-v6-motor.html
42 - 47psi with engine OFF ----- I had engine ON with 23psi
http://www.justanswer.com/buick/3nro...-v6-motor.html
42 - 47psi with engine OFF ----- I had engine ON with 23psi
Last edited by danjamesjr; 02-25-2014 at 08:44 PM.
#19
Senior Member
True Car Nut
that seems more like a regulator issue. shouldnt go down that far, what do you have engine on vacuum line disconnected? try smelling the vacuum port on the regulator, if you can smell gas its bad and leaking past the seals
#20
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Feb 2014
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts