Aurora Hub change....Link
#1
Senior Member
Expert Gearhead
Thread Starter
![Default](https://www.gmforum.com/images/icons/icon1.gif)
I wont type this one again..lol
http://aurorah.proboards20.com/index...num=1091471732
Read on if yer interested
http://aurorah.proboards20.com/index...num=1091471732
Read on if yer interested
![Wink](https://www.gmforum.com/gm/images/smilies/wink.gif)
#2
Senior Member
Posts like a Corvette
Join Date: Jan 2004
Location: Montréal, QC
Posts: 1,374
Likes: 0
Received 0 Likes
on
0 Posts
![Foghorn is on a distinguished road](https://www.gmforum.com/images/reputation/reputation_pos.gif)
![Default](https://www.gmforum.com/images/icons/icon1.gif)
These 2 items would have helped a lot;
A Slide Hammer Puller will take that hub off easily;
![](http://www.cedarcreektools.com/i/Performance%20Tec/tn_W89725.jpg)
WD40 is next to useless as a penetrating oil;
![](http://www.gunk.com/cat_images/L112.JPG)
Looks like you had a good time at least
Cheers,
A Slide Hammer Puller will take that hub off easily;
![](http://www.cedarcreektools.com/i/Performance%20Tec/tn_W89725.jpg)
WD40 is next to useless as a penetrating oil;
Looks like you had a good time at least
![Roll Eyes](https://www.gmforum.com/gm/images/smilies/rolleyes.gif)
Cheers,
#3
Senior Member
Expert Gearhead
Thread Starter
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Yeah, liquid wrench came in handy, we used it as well as the WD40...but slide pull hammer eh? Hrm...never thought of that...thanks!
#4
Senior Member
True Car Nut
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Did you check the make sure the teeth on the spindle wasn't FAA Zooed up?? lookin @ the back piece.. it seemed you pry where it attatched to the spindle. This may cause issue if it was mangled (teeth warn and bent in spots ) a bit for the next removal.. and or even worse. (teeth worn and bent or rounded )
But glad you did it.. yes yes... now we know why god created swear words..
But glad you did it.. yes yes... now we know why god created swear words..
![Twisted Evil](https://www.gmforum.com/gm/images/smilies/icon_twisted.gif)
#5
Senior Member
Expert Gearhead
Thread Starter
![Default](https://www.gmforum.com/images/icons/icon1.gif)
We definitely stayed away from the teeth on the driveshaft and the CV boot, for obvious reasons, but the hub when in without an issue (albeit a bit snug).
No problems to report thus far.
No problems to report thus far.
![Smile](https://www.gmforum.com/gm/images/smilies/smile.gif)
#6
Senior Member
True Car Nut
![Default](https://www.gmforum.com/images/icons/icon1.gif)
Thats good to hear..
Jim.. you are earning your nickname this week haven't you.....
You're just lucky I don't have yellow pi$$y supasta powa... or I"d add a line to your sig.. and it would go something like
"JIM "THE TOOLMAN" WALLACE.. hurr hurrr hurrr"
Jim.. you are earning your nickname this week haven't you.....
You're just lucky I don't have yellow pi$$y supasta powa... or I"d add a line to your sig.. and it would go something like
"JIM "THE TOOLMAN" WALLACE.. hurr hurrr hurrr"
Thread
Thread Starter
Forum
Replies
Last Post
valerka
Bonneville GXP/ Northstar Powered Cars
6
08-26-2004 12:08 AM