Ohm Question
#1
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2005
Location: South Florida
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Ohm Question
Ok, previous post was about selling RF - 301M amps. Those were 2 Ohm load amps.
The amp I am looking at getting is a T20001bd Mono (used) amp.
At 1 Ohm the amp puts out 2800 watts
At 2 Ohm = 2000 watts
at 4 Ohm = 1500 watts
Ok, my goal is to run it at 4 ohms into two P3 Dual voice coil 2 Ohm speakers. I was told I could not. I could either run the T20001bd at 1 Ohm or 8 Ohm only. Well 1 Ohm will definately kill my speakers. 8 Ohm, not worth the upgrade.
I do not want to buy new speakers, I would like to keep my current ones, (Save money)
Is there a way to make this work? Run the amp at 4 Ohm into my P3 12"'* 2 Ohm dual voice coil speakers? Some way to make it work by fancy wiring or whatever?
Sorry I am not a electronics guy.
Thanks for the input guys.
The amp I am looking at getting is a T20001bd Mono (used) amp.
At 1 Ohm the amp puts out 2800 watts
At 2 Ohm = 2000 watts
at 4 Ohm = 1500 watts
Ok, my goal is to run it at 4 ohms into two P3 Dual voice coil 2 Ohm speakers. I was told I could not. I could either run the T20001bd at 1 Ohm or 8 Ohm only. Well 1 Ohm will definately kill my speakers. 8 Ohm, not worth the upgrade.
I do not want to buy new speakers, I would like to keep my current ones, (Save money)
Is there a way to make this work? Run the amp at 4 Ohm into my P3 12"'* 2 Ohm dual voice coil speakers? Some way to make it work by fancy wiring or whatever?
Sorry I am not a electronics guy.
Thanks for the input guys.
#3
Senior Member
Posts like a Corvette
Join Date: Feb 2007
Location: Sanford Michigan
Posts: 1,201
Likes: 0
Received 0 Likes
on
0 Posts
I would say run a 2 ohm load, just turn down the gain on the amp.
Get a two ohm load by wiring each speakers two voice coils in series. This will give each speaker a 4 ohm rating. Then take the wires from each speaker and run them parallel to the amp for a total overall load of 2 ohm.
Get a two ohm load by wiring each speakers two voice coils in series. This will give each speaker a 4 ohm rating. Then take the wires from each speaker and run them parallel to the amp for a total overall load of 2 ohm.
#4
Senior Member
Posts like a Camaro
Join Date: Feb 2003
Location: Indianapolis, IN / West Lafayette
Posts: 1,004
Likes: 0
Received 0 Likes
on
0 Posts
Yah, you can not run 4 ohm because the way the resistance is set up on the speakers. 2 ohm would not kill them just turn the gain down...here is a wiring diagram
you can find more on cardomain and crutchfields pages.
you can find more on cardomain and crutchfields pages.
#5
Senior Member
Posts like a Corvette
Join Date: Feb 2007
Location: Sanford Michigan
Posts: 1,201
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Plurr
Yah, you can not run 4 ohm because the way the resistance is set up on the speakers. 2 ohm would not kill them just turn the gain down...here is a wiring diagram
you can find more on cardomain and crutchfields pages.
you can find more on cardomain and crutchfields pages.
#6
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2005
Location: South Florida
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
So at 2 Ohms the amp puts out close to 2000 watts.
My P3'* can handle RMS 500 watts, Peak 1000 watts.
I am trying to understand "Gain" here. From what I am reading, setting it at 2 OHm and turning the Gain down, means it will pump out less than 2000 watts?
As long as I get close to 750 watts per speaker, I think I am safe.
By turning the gain down, is there a way to know how much watts your pushing to the speakers?
Is there a site for a primer on Gain? so i can understand what that does.
Thanks guys, alot!
My P3'* can handle RMS 500 watts, Peak 1000 watts.
I am trying to understand "Gain" here. From what I am reading, setting it at 2 OHm and turning the Gain down, means it will pump out less than 2000 watts?
As long as I get close to 750 watts per speaker, I think I am safe.
By turning the gain down, is there a way to know how much watts your pushing to the speakers?
Is there a site for a primer on Gain? so i can understand what that does.
Thanks guys, alot!
#7
Senior Member
Posts like a Camaro
Join Date: Feb 2003
Location: Indianapolis, IN / West Lafayette
Posts: 1,004
Likes: 0
Received 0 Likes
on
0 Posts
All the gain does is sets how much the amplifier outputs to the speaker. You want to set it low and work your way turning it up until you have it set where you want it. You want to make sure your speakers are not distorting. Make sure you set the gain to accommodate for the maximum volume that you will listen to the speakers, so that way you do not blow them by overpowering them, when you crank it up. The gain is usually a little ****, sometimes you have to use a screwdriver to twist it to adjust it. If you use a second gain **** or a "bass boost" **** make sure you have that turned up when adjusting the manual gain on the amp so that if you change the bass level on the bass boost **** it doesn't send too much power to your speakers.
#9
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2005
Location: South Florida
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
I was wrong
Ok, I thought I had 2 ohm speakers but they are 4 ohm, wired in series to except 2 ohm setup from my current amps.
I have 4 ohms speakers and there for the t20001bd will not work for me because I can only use it at either 1 Ohm or 4 Ohm.
1 Ohm will blow the speakers
4 Ohm doesn't really help me, at least not for the money.
Thanks guys for the input.
I have 4 ohms speakers and there for the t20001bd will not work for me because I can only use it at either 1 Ohm or 4 Ohm.
1 Ohm will blow the speakers
4 Ohm doesn't really help me, at least not for the money.
Thanks guys for the input.
#10
Senior Member
True Car Nut
Join Date: Sep 2004
Location: Fitchburg Ma _ToastedRice_
Posts: 6,837
Likes: 0
Received 3 Likes
on
3 Posts
Re: I was wrong
Originally Posted by myrddin70
Ok, I thought I had 2 ohm speakers but they are 4 ohm, wired in series to except 2 ohm setup from my current amps.
I have 4 ohms speakers and there for the t20001bd will not work for me because I can only use it at either 1 Ohm or 4 Ohm.
1 Ohm will blow the speakers
4 Ohm doesn't really help me, at least not for the money.
Thanks guys for the input.
I have 4 ohms speakers and there for the t20001bd will not work for me because I can only use it at either 1 Ohm or 4 Ohm.
1 Ohm will blow the speakers
4 Ohm doesn't really help me, at least not for the money.
Thanks guys for the input.