aftermarket alarm *(viper 791 xv install)* updated diagrams
#22
Senior Member
True Car Nut
Let'* compare notes:
H1/1 No connection
H1/2 Brown; above driver’* hush panel above gas pedal
H1/3 No connection
H1/4 Optional. Input to relay, output to same wire as H1/5
H1/5 White. Underdash light. **other details**
H1/6 No connection
H1/7 No connection
H1/8 Ground
H1/9 No connection
H1/10 To siren red wire
H1/11 Red; Steering column harness. May be combined with either red wire from heavy gauge inline connector key switch interface
H1/12 Input to relay for trunk release. Output to (need confirmation) behind left kick panel
H2/1 Lt green; Left kick or door jamb boot
H2/2 No connection (?)
H2/3 Option; input to relay for ch 4
H2/4 Option; input to relay for ch 5
H2/5 No connection
H2/6 Option; input to relay for 2nd stage unlock
Door lock harness, 3-pin connector
1 black (may be white); left kick or door jamb boot
2 No connection
3 light blue; left kick or door jamb boot
Remote start primary harness, 7-pin connector
This just plugs into the module and into the satellite relay
Heavy gauge inline connector key switch interface
1 Cut yellow wire; connect to “starter” side; steering column harness
2 Cut yellow wire; connect to “key” side; steering column harness
3 Red; steering column harness
4 Orange; steering column harness
5 Pink; steering column harness
6 2nd red or red/white; steering column harness
7 No connection; **other details**
8 No connection; **other details**
Remote start secondary harness (H3),5-pin connector
H3/1 Status input wire of Bulldog 791
H3/2 To hood pin switch. Can use factory switch if diode isolated
H3/3 Light blue; at brake switch above drivers hush panel
H3/4 White or violet/white at ICM
H3/5 No connection
-------------------------------------------------------------------------
I need conformation on the trunk release wire, I think it'* either black or purple/yellow. I have never needed to connect a factory re-arm. I don't think you'll need it but again will need conformation.
The ones labled **other details** will require a lot more information that can be discussed as needed. You also have many options, most of which you will not use. Specific wiring for those options can also be discussed as needed.
Link to full manual
H1/1 No connection
H1/2 Brown; above driver’* hush panel above gas pedal
H1/3 No connection
H1/4 Optional. Input to relay, output to same wire as H1/5
H1/5 White. Underdash light. **other details**
H1/6 No connection
H1/7 No connection
H1/8 Ground
H1/9 No connection
H1/10 To siren red wire
H1/11 Red; Steering column harness. May be combined with either red wire from heavy gauge inline connector key switch interface
H1/12 Input to relay for trunk release. Output to (need confirmation) behind left kick panel
H2/1 Lt green; Left kick or door jamb boot
H2/2 No connection (?)
H2/3 Option; input to relay for ch 4
H2/4 Option; input to relay for ch 5
H2/5 No connection
H2/6 Option; input to relay for 2nd stage unlock
Door lock harness, 3-pin connector
1 black (may be white); left kick or door jamb boot
2 No connection
3 light blue; left kick or door jamb boot
Remote start primary harness, 7-pin connector
This just plugs into the module and into the satellite relay
Heavy gauge inline connector key switch interface
1 Cut yellow wire; connect to “starter” side; steering column harness
2 Cut yellow wire; connect to “key” side; steering column harness
3 Red; steering column harness
4 Orange; steering column harness
5 Pink; steering column harness
6 2nd red or red/white; steering column harness
7 No connection; **other details**
8 No connection; **other details**
Remote start secondary harness (H3),5-pin connector
H3/1 Status input wire of Bulldog 791
H3/2 To hood pin switch. Can use factory switch if diode isolated
H3/3 Light blue; at brake switch above drivers hush panel
H3/4 White or violet/white at ICM
H3/5 No connection
-------------------------------------------------------------------------
I need conformation on the trunk release wire, I think it'* either black or purple/yellow. I have never needed to connect a factory re-arm. I don't think you'll need it but again will need conformation.
The ones labled **other details** will require a lot more information that can be discussed as needed. You also have many options, most of which you will not use. Specific wiring for those options can also be discussed as needed.
Link to full manual
#23
Senior Member
Posts like a Camaro
Thread Starter
Join Date: Feb 2003
Location: Indianapolis, IN / West Lafayette
Posts: 1,004
Likes: 0
Received 0 Likes
on
0 Posts
horray im done with the install and the alarm is awesome only downfall is that the bulldog vats bypass doesnt learn the code so im gonna have to build a resistor and relay deal oh well other than that everything works. the remote start works because I tested it with the key in the ignition and everything works awesome!
#25
Senior Member
Posts like a Corvette
Could you help me out with mine again someday soon? or do i pretty much have all of the info i need on the last post that you linked to here?
#26
Senior Member
True Car Nut
Originally Posted by jachin
Could you help me out with mine again someday soon? or do i pretty much have all of the info i need on the last post that you linked to here?
i was going to do an alarm/remote start 101 tutorial with pics soon. Taking advantage of my interior still being disassembled. There are some things going on with my employer so plans may be changing very quickly, though.
#27
Senior Member
Posts like a Camaro
Join Date: Jul 2004
Location: Canada, Ontario
Posts: 1,090
Likes: 0
Received 0 Likes
on
0 Posts
I just installed the viper 790
This alarm is is pretty cool, added a motorcycle kick stand alarm sensor to my alarm. If my alarm is set and the car gets lifted in any degree up or down or sideways it sets it off, i added this feature beacuse i have seome aftermarket 18" rims. If anybody has any questions feel free to email me.
#28
Senior Member
True Car Nut
Re: I just installed the viper 790
Originally Posted by tripscarcare95
This alarm is is pretty cool, added a motorcycle kick stand alarm sensor to my alarm. If my alarm is set and the car gets lifted in any degree up or down or sideways it sets it off, i added this feature beacuse i have seome aftermarket 18" rims. If anybody has any questions feel free to email me.
#29
Senior Member
True Car Nut
Join Date: Apr 2004
Location: Three Oaks, Michigan
Posts: 4,879
Likes: 0
Received 3 Likes
on
3 Posts
I belive the alarm/sensor will have some leway, and may learn from the posistion at which the alarm was armed.. otherwise yeah, you may not be able to park on hills.
-justin
-justin