Planned mods - am I missing anthing
#1
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Dec 2008
Posts: 175
Likes: 0
From: NW Arkansas
Planned mods - am I missing anthing
1.9 rockers
ceramic power log and crossover
new pulley (NEED INPUTS ON SIZE)
magnaflow high flow cat and mufflers
cooler plugs
72mm TB w/heat shield
shift kit w/ tranny flush and synthetic fluid
kyb gr2s up front monroe max airs out back
13" brakes up front 12" out back
HP tuners
Ported blower
blower spacer
Is there anything else that I need, or are there any pieces/parts here that I don't need?
My goal is not to see how much HP/TQ I can make. Cars are traction limited anyway and FWD cars have more probs with that because of the weight shift. I want to maintain driveability but have power to have fun. The list is just what I want to do. I did the same when I had my 03 cobra. Made a list, did it and ended up with 474.5whp/512wtq. Thanks for your time.
Don
ceramic power log and crossover
new pulley (NEED INPUTS ON SIZE)
magnaflow high flow cat and mufflers
cooler plugs
72mm TB w/heat shield
shift kit w/ tranny flush and synthetic fluid
kyb gr2s up front monroe max airs out back
13" brakes up front 12" out back
HP tuners
Ported blower
blower spacer
Is there anything else that I need, or are there any pieces/parts here that I don't need?
My goal is not to see how much HP/TQ I can make. Cars are traction limited anyway and FWD cars have more probs with that because of the weight shift. I want to maintain driveability but have power to have fun. The list is just what I want to do. I did the same when I had my 03 cobra. Made a list, did it and ended up with 474.5whp/512wtq. Thanks for your time.
Don
Last edited by NWASSEi; 06-29-2009 at 11:37 AM.
#3
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Dec 2008
Posts: 175
Likes: 0
From: NW Arkansas
#5
Joined: May 2006
Posts: 29,661
Likes: 34
From: Sheboygan Wisconsin
Toss a shift lit in ther ewith a canned PCM tune and you might be OK with a 3.4" The tuner is a real good idea, then you can skip the canned tune. With everything you have listed, 30 or 40 hp with a good tune. But there are a lot of factors involved.
#6
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Dec 2008
Posts: 175
Likes: 0
From: NW Arkansas
Don
#7
I would probably think about swapping the ported blower/spacer for a Gen V or intercooler. The Gen 3 blower is still not overly efficient being ported.
From there that would maybe change the TB from a 72mm to a N* or LS1. You must be doing an intake, so that'* not needing to be mentioned.
Looks good overall though. Use the HPT to max timing w/o KR before going smaller on the pulley. In my experienced opinion the 3.4 should be good considering your heads will be the biggest restriction. W/o further flow out...you don't need more flow in, building pressure for the sake of saying you have 15lbs in the intake manifold is great for bragging rights, but bad for temps. Been there..tried that.
From there that would maybe change the TB from a 72mm to a N* or LS1. You must be doing an intake, so that'* not needing to be mentioned.
Looks good overall though. Use the HPT to max timing w/o KR before going smaller on the pulley. In my experienced opinion the 3.4 should be good considering your heads will be the biggest restriction. W/o further flow out...you don't need more flow in, building pressure for the sake of saying you have 15lbs in the intake manifold is great for bragging rights, but bad for temps. Been there..tried that.
#8
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Dec 2008
Posts: 175
Likes: 0
From: NW Arkansas
I would probably think about swapping the ported blower/spacer for a Gen V or intercooler. The Gen 3 blower is still not overly efficient being ported.
From there that would maybe change the TB from a 72mm to a N* or LS1. You must be doing an intake, so that'* not needing to be mentioned.
Looks good overall though. Use the HPT to max timing w/o KR before going smaller on the pulley. In my experienced opinion the 3.4 should be good considering your heads will be the biggest restriction. W/o further flow out...you don't need more flow in, building pressure for the sake of saying you have 15lbs in the intake manifold is great for bragging rights, but bad for temps. Been there..tried that.
From there that would maybe change the TB from a 72mm to a N* or LS1. You must be doing an intake, so that'* not needing to be mentioned.
Looks good overall though. Use the HPT to max timing w/o KR before going smaller on the pulley. In my experienced opinion the 3.4 should be good considering your heads will be the biggest restriction. W/o further flow out...you don't need more flow in, building pressure for the sake of saying you have 15lbs in the intake manifold is great for bragging rights, but bad for temps. Been there..tried that.
Wasn't planning on doing the intake. Do I need to? Will an intercooler fit under the stock hood?
Don
#10
Thread Starter
Senior Member
Posts like a Supercharger
Joined: Dec 2008
Posts: 175
Likes: 0
From: NW Arkansas
Will be doing rockers the same time that I do the blower port job/spacer/gen 5/ which ever one of those happens. That way I don't have to try to do it around the dang blower.
Don
Don