cv axle shaft replacement - SUCCESS!
#1
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Apr 2007
Location: Bountiful, UT
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
cv axle shaft replacement - SUCCESS!
Any tips on how to get the driver'* side axle off the transfer case? I've been prying on it all day long and it does not want to come off!!
#2
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Apr 2007
Location: Bountiful, UT
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
come on nobody'* done this before? I was hoping to find a write-up but the only one i found was for a grand prix. There is no room to pry on anything, nor is there room to fit a puller so how do you get this thing out?
#4
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Apr 2007
Location: Bountiful, UT
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
thats what ive been using for 3 hours! All it wants to do is move back and forth but the axle wont come off the retaining ring. I went and got a slide hammer with several attachments but none of them will hold on or reach around the "cup" of the cv joint. If i had some sort of a fork that would wrap around that "cup" and attach to the slide hammer things would be gravy.
I hate cars sometimes...
I hate cars sometimes...
#5
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Apr 2007
Location: Bountiful, UT
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
ok so after reading the tech info write up it looks like you have to separate the ball joint to get this thing out. Is this the case? If so how does the strut assy. work on these cars? In my grand prix if you separated the lower control arm it was very difficult to re-align everything. If i can get the outboard part of the shaft separated and removed I can then use the slide hammer to remove the tripot.
#6
Senior Member
Posts like a Northstar
Join Date: Mar 2007
Location: Maumee, OH
Posts: 529
Likes: 0
Received 0 Likes
on
0 Posts
I didn't have to seperate the ball joint. I undid the spindle, left the ball joint attached, popped the outer end of the CV joint out of the spindle, and swung it aside. I then had a crap load of free room to pop it out of the tranny.
Except for not having the correct sized hub socket, I was done in about 1.5 hours.
IIRC, getting it to pop out was a helluva lot easier than getting the lock ring to seat correctly and pop back in.
Except for not having the correct sized hub socket, I was done in about 1.5 hours.
IIRC, getting it to pop out was a helluva lot easier than getting the lock ring to seat correctly and pop back in.
#7
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Apr 2007
Location: Bountiful, UT
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
ok great what do you mean by spindle exactly?
this is what i have undone... I took all this off because thats how you do it on a grand prix.
The brake caliper and rotor are removed.
The wheel hub/bearing is removed.
The boot over the inboard joint on the axle is revoved - so i can get to the grroves that allow you to pull it.
What I see - apparrently I will need to remove the rest of the shaft up to the inboard tripot in order to get a straight shot at it with the slidehammer.
Please help - if I dont need to remove the ball-joint it will make my life alot easier!
this is what i have undone... I took all this off because thats how you do it on a grand prix.
The brake caliper and rotor are removed.
The wheel hub/bearing is removed.
The boot over the inboard joint on the axle is revoved - so i can get to the grroves that allow you to pull it.
What I see - apparrently I will need to remove the rest of the shaft up to the inboard tripot in order to get a straight shot at it with the slidehammer.
Please help - if I dont need to remove the ball-joint it will make my life alot easier!
#8
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Apr 2007
Location: Bountiful, UT
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
ok I have been trying to get the cv axle out for going on 6 hours! there is not enough clearance to remove the shaft with the weels straight or in either lock position. The only way i see to remove it is by dropping the ball joint. I am wondering though...
If I remove the ball joint is the strut tower going to extend downward? Is there anything I need to do to limit that or can I just pop it out and let it go. Also how do i get enough clearance to get the ball joint out when the control arm is pushing up so hard.
Thanks
If I remove the ball joint is the strut tower going to extend downward? Is there anything I need to do to limit that or can I just pop it out and let it go. Also how do i get enough clearance to get the ball joint out when the control arm is pushing up so hard.
Thanks
#9
I have never done this before, but I'm trying to help.
10. Using the J 42129 , disengage the wheel drive shaft from the wheel hub and bearing and support the wheel drive shaft.
11. Assemble the J 2619-O1 , the J 29794 , and the J 33008-A .
12. Using the J 2619-O1 , the J 29794 , and the J 33008-A , disengage the wheel drive shaft (2) from the transaxle (1).
13. Remove the wheel drive shaft from the vehicle.
11. Assemble the J 2619-O1 , the J 29794 , and the J 33008-A .
12. Using the J 2619-O1 , the J 29794 , and the J 33008-A , disengage the wheel drive shaft (2) from the transaxle (1).
13. Remove the wheel drive shaft from the vehicle.
#10
Junior Member
Posts like a Ricer Type-R
OR:
Smack the end of the axle where it comes through the hub with a rubber mallet (leave the nut on there for this to break it loose).
Rotate suspension crap out of the way, and use a large prybar behind the tripod (big 3-winged aluminum thingy part of the axle) with leverage against the tailshaft housing to pop the axle loose.
Smack the end of the axle where it comes through the hub with a rubber mallet (leave the nut on there for this to break it loose).
Rotate suspension crap out of the way, and use a large prybar behind the tripod (big 3-winged aluminum thingy part of the axle) with leverage against the tailshaft housing to pop the axle loose.