Help!... wheel bearing hub (Final update)
#1
Thread Starter
Senior Member
Posts like a Northstar
Joined: Jan 2006
Posts: 598
Likes: 0
From: Valley Forge, PA
Help!... wheel bearing hub (Final update)
edit: new problem see below
I'm sure this is Mechanics 101. I'm replacing the wheel hub. Wheel off, calipers off, axle nut is off. I'm trying to get to the Torx bolts, but I can't rotate the axle more than an inch. So I can't get the holes on the hub over the bolts so I can remove them. Both front wheels are up. I have put the car in neutral and tried to rotate the axle. No dice.
What am I missing? Thanks!
Feelingstupidcharlie
I'm sure this is Mechanics 101. I'm replacing the wheel hub. Wheel off, calipers off, axle nut is off. I'm trying to get to the Torx bolts, but I can't rotate the axle more than an inch. So I can't get the holes on the hub over the bolts so I can remove them. Both front wheels are up. I have put the car in neutral and tried to rotate the axle. No dice.
What am I missing? Thanks!
Feelingstupidcharlie
#2
It should spin in neutral definitely. The other wheel is off the ground right?
-edit and when you tighten the axle nut up, torque it to spec not any more. I crushed a bearing by impacting the axle nut on.
-edit and when you tighten the axle nut up, torque it to spec not any more. I crushed a bearing by impacting the axle nut on.
#4
Thread Starter
Senior Member
Posts like a Northstar
Joined: Jan 2006
Posts: 598
Likes: 0
From: Valley Forge, PA
Originally Posted by 95naSTA
It should spin in neutral definitely. The other wheel is off the ground right?
-edit and when you tighten the axle nut up, torque it to spec not any more. I crushed a bearing by impacting the axle nut on.
-edit and when you tighten the axle nut up, torque it to spec not any more. I crushed a bearing by impacting the axle nut on.
in neutral, the passenger wheel rotates, the driver wheel sdie that I have removed, only moves an inch. Is it because the brake light is on? It somehow locks up because the break light indicator is on? I'm stumped.....
#5
Originally Posted by charliemax
Originally Posted by 95naSTA
It should spin in neutral definitely. The other wheel is off the ground right?
-edit and when you tighten the axle nut up, torque it to spec not any more. I crushed a bearing by impacting the axle nut on.
-edit and when you tighten the axle nut up, torque it to spec not any more. I crushed a bearing by impacting the axle nut on.
in neutral, the passenger wheel rotates, the driver wheel sdie that I have removed, only moves an inch. Is it because the brake light is on? It somehow locks up because the break light indicator is on? I'm stumped.....
I think it'* a leverage issue.
#6
Thread Starter
Senior Member
Posts like a Northstar
Joined: Jan 2006
Posts: 598
Likes: 0
From: Valley Forge, PA
OK. I told you it was stupid. I had gotten one bolt loose, but didn't back the bolt out completly because the hole wasn't aligned. It was hitting a flange or something that I couldn't see behind the hub, stopping the rotation.
Thanks and please continue with your regular scheduled programming.....
Seriously thanks, I would have wasted hours if you guys hadn't confirmed I was doing everything else correctly.
Thanks and please continue with your regular scheduled programming.....
Seriously thanks, I would have wasted hours if you guys hadn't confirmed I was doing everything else correctly.
#8
Senior Member
Posts like a Turbo
Joined: Jul 2003
Posts: 239
Likes: 0
From: Markham, Ontario, Canada
I just did the wheel bearing on my van last weekend. Couldn't figure out for an hour how to get good leverage on the rear bolts. Until my brother arrived and told me to turn the wheel.
#9
Thread Starter
Senior Member
Posts like a Northstar
Joined: Jan 2006
Posts: 598
Likes: 0
From: Valley Forge, PA
Part II -
So I'm pounding on the hub to get it off, coming slow. I get it away from the housing.... get two pry bars behind... and out it comes.... axle and all. I'm assuming that is the knuckle it is still attached to. Am I cooked, or can I just figure a way to push that spindle back out? I thought I broke it back from the hub when I started. Was i supposed to pound it all the way back?
Advice welcome and some razzing if it'* good spirited....
Imgonnadothischarlie
So I'm pounding on the hub to get it off, coming slow. I get it away from the housing.... get two pry bars behind... and out it comes.... axle and all. I'm assuming that is the knuckle it is still attached to. Am I cooked, or can I just figure a way to push that spindle back out? I thought I broke it back from the hub when I started. Was i supposed to pound it all the way back?
Advice welcome and some razzing if it'* good spirited....
Imgonnadothischarlie
#10
Did you pull the whole axle out? don't pound it.. They pop back in..
Next time when the axle nut is almost fully off..leaveit on so it'* almost flush with the end of the axle and give it a couple good whacks to break the stuckedness.
Next time when the axle nut is almost fully off..leaveit on so it'* almost flush with the end of the axle and give it a couple good whacks to break the stuckedness.