FL Wheel Bearing replacement ?
#11
Thread Starter
Junior Member
Posts like a Ricer Type-R
Joined: Feb 2006
Posts: 14
Likes: 0
From: Near Niagara Falls Canada
Okay, well it sounds like the axle slips through the ID of the bearing inner race without much friction and it should come apart with no more than a little helpful persuasion.. I'm used to tight fiting bearings where a puller is required to separate the bearing from the shaft/axle.
Now I'm better prepared, visuals and all !
Thanks again.
Hugh
Now I'm better prepared, visuals and all !
Thanks again.
Hugh
#12
Originally Posted by Maymybonneliveforever
What would be a resonable amount of time to re & re each one? I need to do it when it gets warmer out and would like to have an idea.
Thanks everyone.
Thanks everyone.
Let me try and ask that question again.................What would be a reasonable amount of time to re & re a wheel bearing?
#14
Thanks for the response markwb, that being said then I should be able to do both side plus the supercharger couple easily in a weekend?......This I have to see..... If that be the case then drinks are on the house! I'll let you all know when I get the parts. WoooooHoooooo. Sorry folks..........been a long couple of weeks and I've had a few, to .........how you say........get me to sleep quickly.. I want to get this bonne on the road so bad that I can't wait to get all the parts.
Patience grasshopper.........Patience.......
Patience grasshopper.........Patience.......
#15
Thread Starter
Junior Member
Posts like a Ricer Type-R
Joined: Feb 2006
Posts: 14
Likes: 0
From: Near Niagara Falls Canada
I found a place called "Wheel Bearings Inc" who sell the wheel bearing-hub assembly that I need (p/n 513087), complete with ABS sensor for $69. They claim that their parts are manufactured with American made, or OEM bearings. Seems like a pretty good price compared to other vendors that I've seen on the net. Anyone had dealings with this company ?
Thanks, Hugh
Thanks, Hugh
#17
Thread Starter
Junior Member
Posts like a Ricer Type-R
Joined: Feb 2006
Posts: 14
Likes: 0
From: Near Niagara Falls Canada
#18
That is a great price.
To answer your previous question, the axle shaft is deeply splined to mate with splines on the center of the hub assembly. Lots of times, once you have loosened the big nut, the shaft will push partway in through the hub (notice the penetrating oil). Other times, you have to wop the shaft to pop it loose from the hub. Beating on the shaft is a bad idea for expensive joint and transaxle reasons. If the shaft is rusted tightly to the hub, you may need to rent a puller to force it to move. With the hub assembly in place, there is not room for the shaft to push all the way through without separating the ball joint and tie rod end. But you are not pushing the shaft through, you are unbolting the hub and sliding it off the shaft.
To answer your previous question, the axle shaft is deeply splined to mate with splines on the center of the hub assembly. Lots of times, once you have loosened the big nut, the shaft will push partway in through the hub (notice the penetrating oil). Other times, you have to wop the shaft to pop it loose from the hub. Beating on the shaft is a bad idea for expensive joint and transaxle reasons. If the shaft is rusted tightly to the hub, you may need to rent a puller to force it to move. With the hub assembly in place, there is not room for the shaft to push all the way through without separating the ball joint and tie rod end. But you are not pushing the shaft through, you are unbolting the hub and sliding it off the shaft.
#19
Thread Starter
Junior Member
Posts like a Ricer Type-R
Joined: Feb 2006
Posts: 14
Likes: 0
From: Near Niagara Falls Canada
Thanks for the clarification Bill.
It looks like a job that I should have no trouble with (I hate surprises).
I'm going to order a new bearing assembly from Wheel Bearings Inc and give it a try when the weather warms up a little. (It'* still below freezing here but should start warming up through this month).
I also have a rattling coupler to change in the supercharger of my GTP. Lots 'o fun !
Hugh
It looks like a job that I should have no trouble with (I hate surprises).
I'm going to order a new bearing assembly from Wheel Bearings Inc and give it a try when the weather warms up a little. (It'* still below freezing here but should start warming up through this month).
I also have a rattling coupler to change in the supercharger of my GTP. Lots 'o fun !
Hugh